Parts for a Cerbera V8
We have 154 parts for a Cerbera V8.
DIFFERENTIAL BUSH : PART NO. TVR 013 (REPLACES R0063 AND R0064)
High quality polyurethane upgrade bush for differntial of Griffith (except very early models), Chimaera and all later models. Very easy to fit without the need for special tools. Three required per car; two at the front and one at the rear of the differential. PRICED PER BUSH
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Tamora, Cerbera SP6, Tuscan2, Sagaris
Price: £19.92
ex VAT £16.95
LIGHTENED AJP V8 FLYWHEEL, PART NO RP024
Raceproved AJP V8 Superlight Steel billet flywheels have been developed to increase engine performance. Horse power which would normally be absorbed by a heavy standard cast iron flywheel is now freed-up, and goes straight to the wheels. Extensive dyno testing has proven acceleration gains of 10 bhp over standard. A 34% weight reduction is achieved by using chromium molybendum steel instead of factory standard cast iron. Chromoly steel has fantastic tensile strength compared with iron, and therefore the flywheel is designed using much less material. Once machined, the flywheels are nitrided for durability, and to reduce wear from AP clutch butterfly spring contact. The starter ring gear is incorporated into the billet to give an elegant one-piece flywheel. The gear tooth profile of our flywheels is bespoke, and has been optimised for the Cerbera’s Tilton starter. This has been proven to improve many of the problems associated with the standard ring gear, and should enhance the lifespan of your starter motor. Our flywheels are made without compromise to the highest quality, giving your car a crisper throttle response and keen acceleration, whilst still retaining the smooth idle and superb driveability.
Fits: Cerbera V8
Price: £385.40
ex VAT £328.00
HOSE AND CLIP SET: PART NO HK007B
Complete silicone hose kit carefully manufactured for easy fitting. Supplied complete with all clips and instructions. Fits Cerbera V8 early models (1996 - 1997). Standard colour is blue but can be supplied in Purple, Green, Yellow or Red (special order approximately 4 weeks delivery). We can supply kits for the majority of TVR models; please contact us for details.
Fits: Cerbera V8
Price: £203.28
ex VAT £173.00
HOSE AND CLIP SET: PART NO HK007
Complete silicone hose kit carefully manufactured for easy fitting. Supplied complete with all clips and instructions. Fits Cerbera V8 models. Standard colour is blue but can be supplied in Purple, Green, Yellow or Red (special order approximately 4 weeks delivery). We can supply kits for the majority of TVR models; please contact us for details.
Fits: Cerbera V8
Price: £185.65
ex VAT £158.00
GEARBOX REMOTE BUSH, PART NO T51
POWER STEERING HOSE KIT: PART NO. H0636
PROP SHAFT BOLT KIT: PART NO. BOLK1
It is always best to replace bolts that are under a lot of tension when doing work on your car and this particularly applies to the prop shaft. A complete kit of bolts for your peace of mind. PRICED PER KIT
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Tamora, M Series, Tasmin, Wedge, Cerbera SP6, S - Series, Tuscan2, Sagaris
Price: £5.88
ex VAT £5.00
CHROME VALVE CAPS : PART NO. VALV8
These extremely high quality dust caps are finished off with the TVR logo. They will really provide that finishing touch to your wheels. PRICED PER SET OF FOUR
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Tamora, M Series, Tasmin, Cerbera SP6, S - Series, Tuscan2, Sagaris
Price: £7.99
ex VAT £6.80
COASTER :PART NO. COAS1
These stylish coasters have been designed to look like a wheel centre with the TVR logo. Buy a set and impress your friends when you sit down together for a quiet drink after a drive. PRICED PER COASTER
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Tamora, M Series, Tasmin, Wedge, Cerbera SP6, S - Series, Tuscan2, Sagaris
Price: £4.11
ex VAT £3.50
FILTERMAG : PART NO. CTFM
Give your engine the ultimate in protection by clamping one of these simple but powerful magnetic devices to your oil canister. The Filtermag has an overall unidirectional magnetic force of several hundred pounds on one side while it will not hold a paperclip on the other. This extremely concentrated magnetic field not only secures the unit to the filter canister but also attracts all the metallic particles that the filter itself would not remove from the oil. The unit is fully re-usable and is just transferred from the old to new filter during a service. It will last for 50 years and maintains its magnetic strength even when the temperature exceeds 200F. This unit is a must for hard working engines and will significantly help reduce engine wear recovering the initial cost in no time at all. Comes complete with full instructions for use. IT DOES NOT REDUCE THE NEED FOR REGULAR SERVICING AND OIL CHANGES. BUY NOW AT OUR BARGAIN PRICE
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Tamora, M Series, Tasmin, Wedge, Cerbera SP6, S - Series, Tuscan2, Sagaris
Price: £37.01
ex VAT £31.50
WIPER MOTOR NEW, PART NO M0195
MAP SENSOR, PART NO E2661
REAR ANTI ROLL BAR DROP LINKS: PART NO. LD0332
ALLOY CERBERA AIR FILTER OIL BREATHER: PART NO. RT005
ALLOY CERBERA HEADER TANK: PART NO RT004
CERBERA, CHIMAERA,GRIFFITH ALLOY RADIATOR: PART NO. RT003
High quality, high efficieny alloy radiator that fits all models, both air-conditioning and no air-conditioning. Fitment is exactly as original. Complete with an aluminium cowl that has pre-threaded holes to accept fans(FANS NOT SUPPLIED)
Fits: Cerbera V8, Griffith, Chimaera, Cerbera SP6
Price: £446.50
ex VAT £380.00
WIPER MOTOR, RECONDITIONED, PART NO M0195R
Wiper motor reconditioned, no longer available new, some late Chimaeras will have the Bosch type wiper motor, this motor is fitted on the N/S inner wing, the price includes a £50.00 surcharge which is refunded when the old unit is returned and found to be suitable for reconditioning.
Fits: Cerbera V8, Griffith, Chimaera, Cerbera SP6
Price: £293.74
ex VAT £249.99
MINI SEALEY TROLLEY JACK: PART NO. JACK1
This is an extremely high quality mini trolley jack. It is manufactured from aluminium and is a fully operational minature version of a race mechanics trolley jack. Perfect in every respect and capable of lifting 100kgs. Pointless but perfect. Buy one now as stock is very limited and may not be repeated.
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Tamora, M Series, Tasmin, Wedge, Cerbera SP6, S - Series, Tuscan2, Sagaris
Price: £35.25
ex VAT £30.00
HEAVY BRUSHED PRO-STYLE BASEBALL CAP PART NO. HAT1
Top quality 100% heavy brushed cotton drill baseball cap. Self fabric strap with tri-glide buckle and sandwich peak. In black with silver TVR logo. LIMITED STOCK AT THIS PRICE
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Tamora, M Series, Tasmin, Wedge, Cerbera SP6, S - Series, Tuscan2, Sagaris
Price: £14.04
ex VAT £11.95
KEY RING: PART NO. KRB02
KEY RING: PART NO. KRB01
THROTTLE CABLE: PART NO E2738
REAR BRAKE SPLIT PIN: PART NO J0189
DRIVE SHAFT CV JOINT, PART NO R0040
BRAKE FLUID RESERVOIR CAP, PART NO J0090
DIFFERENTIAL DRAIN PLUG, PART NO R0296
FUEL CAP, PART NO L0069
THROTTLE CABLE REPAIR KIT, PART NO TVR046
FUEL FILTER, PART NO L0180
OIL FILTER, PART NO E2117
CAR MATS: PART NO. TCM001
High quality car mats custom made to fit your car perfectly. These mats are made to order and delivered to you direct from the manufacturer. They are available in a choice of 6 colours and 18 different bindings. They can also have either carpet heelpads or metal plates on driver side only or passenger side as well. There is a selection of logos available or you can design your own. Because of the number of options available we need you to complete a requirements form before we can process your order. Contact us for the requirements form and on its return we will calculate the total cost of the mats. Once we have received payment the order will be placed and the mats are normally delivered within five working days. PLEASE NOTE THAT BECAUSE THIS ITEM IS MADE TO ORDER IT IS NON-RETURNABLE UNLESS THERE IS A FAULT. Prices start at £60.00 + VAT per set We can also offer an additional service if you require mats made to match these for another part of your car such as the parcel shelf. If you provide us with a template of the area then we can obtain a price for a matching bespoke mat.
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Tamora, M Series, Tasmin, Wedge, Cerbera SP6, S - Series, Tuscan2, Sagaris
Price: £70.50
ex VAT £60.00
PROTECTIVE WING COVER, PART NO TVR044
Protect the paintwork on your car when working in the engine bay by using our exclusive wing cover. It provides ultimate protection against accidentally dropped tools and scratches from buttons, zips,buckles etc. It is simple and extremely easy to use as it simply drops onto the wing of a car and being made from rubber it naturally grips the vehicle bodywork without abrasion. As these wing covers are non-magnetic they will not upset any electronic controls in the engine bay or give mis-readings to analysis equipment being used. NOTE THIS COVER IS FULLY WASHABLE BUT IT MUST NOT BE TUMBLED, DRIP DRY ONLY. EXTRA SPECIAL OFFER - ONLY A FEW AT THIS PRICE.
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Tamora, M Series, Tasmin, Wedge, Cerbera SP6, S - Series, Tuscan2, Sagaris
Price: £14.04
ex VAT £11.95
WINDSREEN WASHER MOTOR AND PUMP, PART NO TVR042
WASHER BOTTLE CAP, PART NO M0667
GEARBOX INPUT SEAL: PART NO T45F054R
TAILSHAFT SEAL T5, PART NO T45F167R
RADIATOR MOUNTING BOBBIN, PARTNO K0092
HEADLAMP BOOT, PART NO TVR040
TRACK ROD END, PART NO H0314
DUAL OIL AND WATER GAUGE, PART NO N0157R
Dual gauge oil pressure and water temperature, with MAGNOLIA face, this a fully reconditioned unit by the original manufacturer, this gauge is no longer available new, so your old unit must be returned, a surcharge of £100.00 is included in the price, which will be refunded once the old unit is received and found to be in a suitable condition for reconditioning.
Fits: Cerbera V8, Cerbera SP6
Price: £251.07
ex VAT £213.68
CLEVER TREVOR SPARE BULB KIT : PART NO. BUL004
Spare bulb kit containg 1 x H4 headlamp bulb (suitable for Cerbera and Chimaera) plus a selcetion of other bulbs and two blade fuses to keep you running in the dark.All packed in foam and contained in a plastic box for protection. A KIT SUCH AS THIS IS A LEGAL REQUIREMENT IF DRIVING ON THE CONTINENT. We can also supply additional or other bulbs, including Xenon, to order. Contact us for details.
Fits: Cerbera V8, Chimaera, Cerbera SP6
Price: £5.88
ex VAT £5.00
DOUBLE ADJUSTABLE S/ABS & SPRING SET, PART NO PT2
PRO-TECH SHOCKS 600 SERIES are made from 52 M/M diameter 6262 specification aluminium with adjustable spring seat platform for 2 ¼" I.D. springs. The 600 SERIES has independent bump and rebound adjustment, this allowed valving changes to be made at all shaft velocities without effecting the other valving adjustments. These shocks will give you the advantage over the competition at which a tyre is loaded or unloaded during dynamic weight transfer. Dynamic weight transfer is the transferring of weight from side to side during cornering, from rear to front during deceleration and from front to rear during acceleration. By changing the stiffness of the shock's independently on the racecar, we are adjusting the loadings on the tyres at different points on the racetrack, if done correctly good handling will result in getting you to the chequered flag first! All units are hand built and come complete with all fittings and springs, allow 10 days delivery. Please specify vehicle details when ordering.
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Cerbera SP6
Price: £1092.75
ex VAT £930.00
PROTECH SHOCK ABSORBER/SPRING SET, PART NO PT1
Protech shock absorbers, are a high quality product suitable for fast road use and track days, at an affordable price and come complete with springs, adjustable spring platforms and adjustable damping. The control knob has only 13 click settings with a total movement of 300 degrees (less than one turn). A new internal sealing system is designed to eliminate high pressure bleeding so all movement of oil in bump and rebound is consistently controlled through the piston and base valve. These units are ultra light weight all aluminium design and the components used are C.N.C machined to a very high standard, they are then anodised in clear and black to give maximum protection and presentation. (All units are hand built to order). Please specify details of the car when ordering, allow 10 days delivery, comes complete ready to fit, with 3 years warranty. Suitable for Griffith, Chimaera, Cerbera, Tuscan, T350.
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Cerbera SP6
Price: £670.93
ex VAT £571.00
HEADLAMP ADJUSTERS 70MM KIT, PART NO TVR039
MIRRORED REPEATER BULB, PART NO BUL002
CERBERA STARTER MOTOR NEW, PART NO E2101
WASHER TUBING: PART NO M0328.
REFLECTIVE HEAT MAT, PART NO S0039
Heat reflective mat, 1mm thick x 1 metre wide woven fibreglass mat with reflective surface. Suitable for making under bonnet and bulkhead heat shields. SOLD PER SQUARE METRE. Fix in place with High Temperature Silicone (Part No. TVR028) and cover joins with Aluminium Foil Tape (Part No. MS025)
Fits: Cerbera V8, Tuscan, Griffith, T350, Chimaera, Tamora, M Series, Tasmin, Wedge, Cerbera SP6, S - Series
Price: £33.78
ex VAT £28.75
EXPANSION VALVE, PART NO P0224
REMOTE CLUTCH BLEED PIPE: PART NO Q0111
Remote clutch bleed pipe, manufactured with stainless fittings, fitted with larger 11mm spanner size bleed nipple.
Fits: Cerbera V8, Tuscan, T350, Tamora, Cerbera SP6
Price: £24.56
ex VAT £20.90
DIFFERENTIAL FILLER PLUG, PART NO R0299
DIFFERENTIAL REAR COVER, PART NO TVR034
WINDOW LIFT MOTOR, PART NO TVR033
DAMPER BUSH, PART NO C0092
MIRRORED INDICATOR BULB, PART NO BUL001
STEERING RACK PINION SEAL, PART NO H0293
PIPERCROSS PERFORMANCE AIR FILTER, PART NO PCE2584
REAR SUSPENSION BUSH, PART NO D0104
SUSPENSION BUSH, PART NO C0200
EBC FRONT BRAKE PAD SET, PART NO EBCJ0176 - BRAKE PADS
Front brake pad set manufactured by EBC. This material is a Kevlar® fibre based brake compound enhanced with ceramic particles. If you have previously tried EBC redstuff (pre-ceramic compound) this material is light years ahead. It lasts longer, it brakes better and is quieter. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).
Fits: Cerbera V8, Cerbera SP6
Price: £55.67
ex VAT £47.38
EBC REAR BRAKE PAD SET, PART NO EBCJ0177 - BRAKE PADS
Rear brake pad set, manufactured by EBC, This material is a Kevlar® fibre based brake compound enhanced with ceramic particles. If you have previously tried EBC redstuff (pre-ceramic compound) this material is light years ahead. It lasts longer, it brakes better and is quieter. Being a hard wearing pad, bed-in times can be as long as 1000 miles and drivers must be patient until the pad takes up the shape of their disc (brake rotor).
Fits: Cerbera V8, Cerbera SP6
Price: £38.74
ex VAT £32.97
ENGINE MOUNTING, PART NO E2814
Engine mounting. Fits Cerbera V8 4.2 and 4.5; NOT Speed Six.
Fits: Cerbera V8
Price: £23.24
ex VAT £19.78
Please contact us for further information concerning availabilty or suitable application.
BOOT SEAL, PART NO U0326
FUEL PUMP, PART NO L0170
HEADLAMP MOUNTING RING, PART NO U1574
META ALARM BATTERY, PART NO TVR031
HEADLAMP ADJUSTER KIT, PART NO TVR030
Headlamp adjuster kit, manufactured in stainless steel with zinc plated spring to resist corrosion, supplied with Bajo lock plate, 3 required per lamp.
Fits: Cerbera V8, Chimaera, Cerbera SP6
Price: £5.83
ex VAT £4.96
FLASHER RELAY, PART NO M0225
WASH WIPE RELAY, PART NO M0778
RADIATOR CAP, PART NO K0060
DOOR OPENING BUTTON, PART NO M0751
Door opening button.
Fits: Cerbera V8, Tuscan, T350, Chimaera, Tamora, Cerbera SP6
Price: £15.18
ex VAT £12.92
DOOR OPENING BUTTON COVER, PART NO M0922
Door opening button waterproof cover.
Fits: Cerbera V8, Tuscan, T350, Chimaera, Tamora, Cerbera SP6
Price: £3.24
ex VAT £2.76
INTERIOR LAMP, PART NO M0780
AIR CONDITIONING CONDENSER, PART NO P0165
RELAY, PART NO M0643
HANDBRAKE SHOE SET, PART NO TVR026
AIR CONDITIONING SUCTION PAD, PART NO P0458
AIR CONDITIONING DISCHARGE PAD, PART NO P0459
ALTERNATOR BELT, PART NO E2943
WIPER BLADE 16 INCH, PART NO M0199
TYRE VALVE CHROME, PART NO G0137
AIR TEMPERATURE SENSOR, PART NO N0112
HORN LOW TONE, PART NO M0131
HORN HIGH TONE, PART NO M0130
DOOR WINDOW RUNNER FELT, PART NO U0399
RECEIVER DRIER, PART NO. P0121
100 AMP BLADE FUSE, PART NO M0615
WINDOW REGULATOR MOTOR,
Window regulator motor, if you have a failed motor and don't want the bother or expense of changing the regulator we can supply the motor only. Suitable for most models from Griffith onwards.
Fits: Cerbera V8, Griffith, T350, Chimaera, Tamora, Cerbera SP6
Please contact us for further information concerning availabilty or suitable application.